How To Repair Internal Antenna Iphone 6

Introduction

Follow the steps in this guide to supersede the upper left antenna in an iPhone 6s.

Before disassembling your iPhone, discharge the battery below 25%. A charged lithium-ion battery can catch fire and/or explode if accidentally punctured.

Before disassembling your iPhone, discharge the battery below 25%. A charged lithium-ion battery tin can grab burn down and/or explode if accidentally punctured.
Power off your iPhone before beginning disassembly.
Remove the two 3.four mm P2 Pentalobe screws on the lesser edge of the iPhone, next to the Lightning connector.

Optionally, apply mild heat to the lower edge of the iPhone using an iOpener or hair dryer for about a minute.

Optionally, apply mild heat to the lower border of the iPhone using an iOpener or hair dryer for about a infinitesimal.
Heat softens the adhesive securing the display, making it easier to open.

Opening the display on the 6s separates a thin strip of adhesive around the perimeter of the display. If you adopt to replace the adhesive, have a set of new adhesive strips ready before yous keep. It's possible to complete the repair without replacing the agglutinative, and you probably won't discover any deviation in functionality.
Apply a suction loving cup to the lower left corner of the display assembly.
Have care not to identify the suction cup over the home button.
If your display is badly cracked, roofing it with a layer of clear packing tape may allow the suction loving cup to attach. Alternatively, very strong tape may be used instead of the suction loving cup. If all else fails, you can superglue the suction cup to the broken screen.

Pull upwards on the suction loving cup with business firm, constant pressure to create a slight gap between the front end console and rear example.
Have your time and apply firm, abiding force. The display associates is a much tighter fit than most devices and is held down with adhesive.
Pulling as well difficult may damage the display assembly. Apply but plenty pressure to create a pocket-size gap between the brandish assembly and the rear case.
If you have any trouble, heat the front of the iPhone using an iOpener, hair dryer, or estrus gun until it's slightly besides hot to touch. This will aid soften the agglutinative securing the edges of the display.

At that place is a notch on the underside of the display, simply above the headphone jack. This is the safest place to begin prying the telephone open.
Place the flat border of a spudger into the gap between the screen and rear case, directly above the headphone jack.

Twist the spudger to widen the gap between the front console assembly and the residue of the phone.

Insert the flat terminate of the spudger on the left side of the telephone, between the brandish assembly and rear instance.
Slide the spudger upwardly the side of the phone to separate the agglutinative and pop the clips free.

Remove the spudger and reinsert it on the lesser edge, where you pried the phone open up.
Slide the spudger to the right, forth the lesser edge of the phone.

Slide the spudger upward the right side to continue separating the agglutinative and popping the brandish clips free from the iPhone.

Apply the suction cup to open the brandish, breaking the last of the adhesive.
Don't open the display more than 90º, every bit it is still connected at the top past three cables that may break if stretched.

Pull upwards on the nub on the meridian side of the suction loving cup to remove it from the forepart panel.

Gently grasp the display assembly and elevator information technology upwardly to open the phone, using the clips at the height of the front panel as a hinge.
Open up the display to about a 90º angle, and lean it against something to keep it propped up while you're working on the phone.
Add together a rubber band to proceed the display securely in place while you work. This prevents undue strain on the display cables.
In a pinch, you can use an unopened canned drinkable to hold the brandish.

Remove two Phillips screws securing the battery connector bracket, of the following lengths:
One 2.9 mm screw
One 2.2 mm screw
Throughout this repair, keep rails of each spiral and make sure it goes back exactly where information technology came from to avoid damaging your iPhone.

Remove the battery connector bracket from the iPhone.

Utilise the point of a spudger to disconnect the bombardment connector by prying information technology direct up from the logic board.

Push button the battery connector away from the logic board until it stays separated from its socket, so as to avoid any adventitious connectedness to the battery while you work.

Remove the following four Phillips screws securing the display cablevision bracket:
Three one.2 mm screws
One 2.8 mm screw

Remove the display cable bracket.

Use a spudger or a clean fingernail to disconnect the front camera flex cablevision by prying it direct upwards from its socket on the logic board.

Disconnect the digitizer cablevision by prying information technology straight upward from its socket on the logic lath.
When reconnecting the digitizer cable, exercise non printing the center of the connector. Press one end of the connector, then press the opposite terminate. Pressing in the middle of the connector tin can bend the component and cause digitizer impairment.

Make sure the battery is asunder before yous disconnect or reconnect the cable in this stride.
Disconnect the brandish cable past prying information technology straight upwards from its socket on the logic board.